Page Comparison

How do I set up a

...

'Collect Data' event for a typical device (pedometer, scale)? 

1. After you add your device to the study, select 'Study Arms' in the left sidebar navigation. Then select 'event Schedule' for the arm where you want to add the device upload 'Collect Data' event.  
   1.  Not sure how to add a device? See 'Collect Data' Event for instructions.
      
      
   
   
   
2. Click the blue 'Add New event' button and select 'Device Upload' as the event type. Then select the source The devices can be viewed by navigating to the Devices section in Manage Study.
   
   Image Added
   
   
3. Select the device options from the drop down list. This will auto populate all of the devices that you have set up in Way to Health.  The devices can be viewed by navigating to the Devices section in Manage Study.  
   Image Removed
   Image Added
   
   
   
4. Name the event. 
   Image Removed
   Leave
   Image Added
   
   
   
5. For daily data collection, typically you want to eave the 'participant message' and 'send notification?' options blank.  
   1.  Tip! To inform the participant  that they should sync their Fitbit or weigh in on their scale every day, send a one-time alert message create a 'Send a Message' event with instructions or welcome to study message. 
      
      
6. Choose the day when the event should start and the event window.  The event window is the time that the participant has to complete either a weigh in or a pedometer sync.  
   1.  Tip! For pedometer or scale device upload events, typically, participants are asked to start weighing in or syncing their pedometers on Day 0 or Day 1 and they have the entire day to do so (12 am - 11:59 pm) 
      Image RemovedImage Added
      
      
7. Indicate how many times the event should repeat and then click the blue 'Add' button 
   1. Tip! For pedometer or scale device upload events, typically, participants are asked to weigh in or sync their pedometer every day for the entire duration of the study. 
      Image RemovedImage Added
      
      
8. You are now ready to build feedback logic on the device upload'Collect Data' event.  Click the 'FeedbackSave and Define Logic' button. 
   Image Removed
   Image Added
   
   
9. Inside the device upload feedback'Collect Data' logic, you can designate compliance criteria. Select If 'Completed and' 
   
   
10. Choose the device field (i.e steps) and the operator (i.e >).  Then select either amount or target.
    1. Amount: a set number for all study participants. For example, 7,000 steps
    2. Target: a individualized step count goal for each study participant 
       1.  Note: In order to use a target for compliance, a target generator must be developed.  
          
          
          
11. Click 'Add a consequence' and select 'compliant' and click the blue 'Save Feedback' at the bottom of the page.
    
    
    
12.  Want to send the participant a message based on the step count total from the previous day? Instead of building this as a feedback logic message directly in the Fitbit event, send the message via a round upan 'Add Logic' event.  See Round Up event for more information on how to set up round up 'Add Logic' events.
    
    
    1. Why should I send the message via a round up'Add Logic'? Otherwise Way to Health will send the feedback message to the participant once the event closes- typically at midnight. Way to Health has a safeguard in place to prevent feedback messages from going out prior to 8 am (unless otherwise specified in the profile), however a participant may not appreciate receiving a text message at 8 am on a Saturday . 
       
       
    2.  But there's a caveat…. If you want to relay the participant's target to them in the daily message (i.e. 'You only walked X steps yesterday and your goal was Y steps.  Try harder today!') then you must build this message onto the device feedback as a round up 'Collect Data' logic as an 'Add Logic' event will not have the option to include the TARGET variable.  
       
       
       

...